1 For use in the UK and ROI NT27 (October 2013)
10 Milan 4 Passive The Milan Passive when connected to an outside dedicated air supply provides all the air for combustion. When the door is closed
11 Milan 4 Passive Figure 1
12 Figure 1 Fitters notes:
13 Apollo 8 Dimensions Apollo 4 Dimension
14 2. Distance to Combustibles 4 Series Rear Side Beaumont 400 350 Belgravia 400 350 Shoreditch 400 350 Shoreditch LS 400 350 Shoreditch XLS 400 3
15 3. Pre Installation This appliance must be fitted in accordance with the current Building Regulations and by an approved HETAS registered insta
16 Chesney’s recommend an appropriate spillage test be conducted with all appliances post installation. Air inlet grilles must be so positioned tha
17 Flue Requirements The chimney must be swept before installation and checked for soundness and suitability. The chimney must also be free from crac
18 4. Installation In addition to these instructions the requirements of BS 8303 and BS EN 15287 must be fulfilled. Local Authority Bylaws and Bui
19 5. Converting Top to Rear Exit The Apollo stoves cannot be rear exit. All other stoves can be converted and are pre-assembled for a top exit. A
2 Congratulations on your purchase of a Chesney’s stove. Please note that it is a legal requirement under England and Wales Building Regulations th
20 10) Refit fire cube, loosely secure fire cube to the cladding using the levelling bolts to line up fire cube with cladding. When in position tight
21 6. Smoke Control The Chesney’s 4,5,6,8 series stoves are DEFRA exempt appliances that can be used in Smoke Control Zones. The “Smoke Tab” is
22 The Clean Air Act 1993 and Smoke Control Areas Under the Clean Air Act local authorities may declare the whole or part of the district of the aut
23 7. Apollo 4 and 8 Installation The Apollo range of inset stoves have been designed to be installed in two stages. The outer casing needs to be i
24 Chimney Connection 1) Drop the liner through the outer casing and fix the flue adaptor, then fit the flue collar to the adaptor bending the adapt
25 8. Door Seal Replacement and Door Handles Always use gloves when handling ceramic rope. Apollo and Milan Remove door from the stove and remove
26 9. Commissioning Check all internal parts are fitted correctly and there are no gaps between the firebricks and baffles and the log retainer is
27 Door Seal Testing and Adjustment Without a good sound airtight seal around the door the stove will not work as designed and will lead to the glas
28 Apollo models The frame and door retainer must be removed before the door can be removed see Apollo information pages. Then rotate the hinge pin c
29 10. The Curing Process Your Chesney’s stove has been designed to operate with minimum effort. As with all wood burning and multi fuel stoves you
3 Contents Section Page 1 Technical Specifications and Dimensions 4 2 Distance to Combustibles
30 11. Stove Paint Application Instructions Chesney’s stove paint is quality, fast drying high temperature paint for use on wood, multi-fuel and ga
31 12. First Lighting and Operation This appliance is not to be used as an incinerator. Only HETAS approved wood logs and smokeless fuels are recom
32 The Wood Range 4 and 5 Series. These are designed for wood burning only although, there is a “drop in multi fuel-grate” available to convert to c
33 Riddling lever illustrated with the red arrow below Air flow bar. Air Flow Bar Settings
34 Wood Setting Wood Setting Setting III primary and secondary air open fully. Air bar is fully extended. Setting II primary air shut secondary
35 Double Sided 10 Series Wood Burning Stove The Double Sided10 has a single air control lever; this controls both primary and secondary air into th
36 Wood Burning 12 Series The 12 series has a single air control lever; this controls both primary and secondary air into the stove. With the cont
37 Baffle The baffle is made up of 4 main parts. The secondary baffle is secured to the top underside of the stove using the slots provided, it’s
38 The Baffle By-pass can be adjusted by undoing the M6 nut and rotating the baffle actuation rod in or out, then retighten the M6 nut. Close the
39 Lighting Open the door place a firelighter at the back of the furnace put 6-8 pieces of kindling on top of the firelighter. Place 2 split logs on
4 1. Technical Specifications and Dimensions Wood Burning 4 Series Parameter Beaumont Belgravia Shoreditch Salisbury Apollo Alpine Milan Nominal h
40 The majority of air for combustion in the coal setting comes from under the grate below the fuel. This action reduces the ability of the air wash
41 13. Maintenance Guarantee Your Chesneys stove comes with a 5 year guarantee on the stove body and a 12 month warranty on the non consumable par
42 Glass seal: still effective Glass not cracked. Fire Bricks: sound. Replace any that have cracks greater than 3mm Baffles: not warped or distorted
43 Useful Information Always use the glove provided when operating or refuelling. The better the quality of fuel you use the better the efficienc
44 Dealer & Installers Details Dealers Name and Contact Details Date of Purchase Installers Name and Contact Details HETAS Reg number
45 Annual Service Record Date Company Name Signature
46 Warranty Registration To validate and start your warranty please fill out this form and send it back to Chesneys, Units 1-4 Zennor Road Business
5 Wood Burning 5 Series Parameter Salisbury Beaumont Shoreditch Nominal heat output kW BTU/hr 4.9 16
6 Multi-Fuel 6 Series Parameters Wood / Ancit Beaumont Belgravia Shoreditch Salisbury Shipton Alpine Milan Nominal heat output
7 Multi-Fuel 8 Series Parameters Wood / Ancit Beaumont Belgravia Shipton Shoreditch Salisbury Apollo Nominal heat output
8 Double 10 Wood Burning Stove Parameters Wood Salisbury Nominal heat output KW BTU/hr 10 / 34121.42 Mean CO emission
9 Wood Burning 12 Series Parameters Wood Salisbury Nominal heat output kW BTU/hr 10.8 / 36851.1336 Mean CO emission
Kommentare zu diesen Handbüchern